Menu FAQmoteur om651Diagnostic automobilep2002 toyotarefirance de boitier reparableboite vitesse automatiqueclass ACODE DIFcodediagnosticVous avez un voyant représentant une clétestesup fapauto-progkey progabout-codeles code de difautrepr fappeuget&actiaelectronicprisontationles code difaut2les code difaut4les code difaut3les code difaut5nvda autoantidemarage hoooeprom transponderFiltre à particulesimagecodage abs et ,,,vcdsreset service oil and number ord peugeot et citroienairbag clio4..ne pas suprime le fapcode difaut dusterUn diesel pour quoi faire des moteurs diesels souffrentDefault antidemarage quranecu dumps airbag adressDésactiver/Activer---fordelm 327GPS Trakercoding control modulIF THE COOLING FANS DO NOT WORKvas5054 with odis instalationclass C204class c 204MERCEDESINTERFACE BIDIRECTIONNELLE MBreprog reneault v113DPF Pressure Sensorcode defaut mercedesActive Regeneration Functionespcode defaut Ucode p245414 m651W203 and W211OM612OM611M272 M273M271M166M166M119 M120M119 M120M112 M113MPC560x ST SPC560Px0 ProgramatorTexas Instruments ProgrammerProgrammer satovaresete niveau d"oil golf5activation lixiacode defaut psahow to use ecusafeLe systeme HDI haute pression Dieselles capteur mbPSA Blue HDiSYSTEME RECYCLAGE DES GAZXPROG M V5.55program the keylessClasse C W205Clim Clavier Class C 205Le spécialiste de la reproginjection LE2-JETRONIC et LU-JETRONIC.Full diagnostic Kit reviewMB STAR NWmoteur om651Le système de protection passif Le systeme HDI (haute pression d’injection Diesel) Common rail

remote controls vw


Procedure for matching radio-frequency remote controls to many VW & Audi vehicles:

Check under Diagnostic Procedures for instructions specific to your vehicle.

Gather ALL the remotes you would like to match. Insert one key in the ignition and turn it ON.

[Select]

[46 - Cent. Conv.]  or [35 - Cent. Locking] (whichever is applicable to the car, as found 

[Adaptation - 10]

Enter channel "01" (May be channel "21" in some Audi models). 

[Read]

This will display the number of currently stored remotes in "Stored Value".

Enter your total number of keys up to a maximum of 4(including any existing keys) in "New Value"

[Test]

Verify that the number in "Test Value" is correct.

[Save]

Then press and hold (for at least one second) the UNLOCK button on the fob, at which time it will be learned. If you're programming more than one fob press and hold the UNLOCK button on the second fob for one second, press and hold the UNLOCK button on the third fob for one second, etc.  You have a total of 15 seconds to do them all.

The car may give you some sort of acknowledgement as each key is learned (lights flash, horn beep, etc.)

If the above procedure does not work (neither Channel 01 nor Channel 21 are available), follow this procedure:

Insert a working (old) key in the ignition and turn to the ON position (do not start car).

[Select]

[46 - Cent. Conv.]  or [35 - Cent. Locking] (whichever is applicable to the car, as found 

[Meas. Blocks - 08]

Enter group "003" (may be group "007" in some vehicles)

 [Go!]

The value in field 2 shows how many remotes have been matched and in which memory positions (for example, "0001" indicates 1 transmitter in position 1).

Lock the car from outside using the new, unmatched key in the driver-side door lock. You may need to hold the key in the unlock position while you do the next step.

Press the UNLOCK button on the new key within 5 seconds often enough to reach next memory position (so, if the value in field 2 was 0001, you should press the new key's unlock button twice, to put the new key in memory position 2)..

The car may give you some sort of acknowledgement as the button is pressed (lights flash, horn beep, etc.)

Wait 5 seconds and press the unlock button on the new key to unlock the door.

Turn the ignition key to OFF and remove the old key. 

Press LOCK and UNLOCK with the new key.

Insert the new key in the ignition and turn to the ON position (do not start car).

[Select]

[46 - Cent. Conv.]  or [35 - Cent. Locking] (whichever is applicable to the car, as found

[Meas. Blocks - 08]

Enter group "003"

 [Go!]

The value in field 2 should now indicate 0011 in the example used, showing the old key still matched in position 1 and the new key matched in position 2.

Make sure that new keys are always coded into free memory positions (where there is a zero in Group 003, field 2). If occupied positions (distinguishable by a "1") are used, the transmitter previously coded to this position will no longer work.

In some cases, it may be necessary to clear out existing matched remotes using the following procedure:

[Select]

[46 - Cent. Conv.]  or [35 - Cent. Locking] (whichever is applicable to the car, as found 

[Adaptation - 10]

Enter channel "00"

[Read]

[Save]

When the prompt asks if you are sure you want to save a value of 0 to Channel 00, click [Yes]

After doing so, no remotes will be matched. You'll need to follow the appropriate above procedure to match all of the remotes.